測硫儀應該注意的幾點事項

1、測硫儀電解池的日常清洗：關閉氣泵/攪拌開關，拔掉電解池上的抽氣管，將電解液放出，接好電解池上的抽氣管，并抽入蒸餾水，打開氣泵/攪拌開關清洗電解池后再將水放干凈。

2、測硫儀解池電極的清洗：一般要求每檢測200個樣品左右，應清洗電極片（如經常分析高硫煤，則此數量還應少一些）。方法如下：拔掉電解池上抽氣嘴及進氣嘴的硅膠管、拔掉電解池上的連線插頭，取下電解池。松開電解池蓋，拿出攪拌子。用一手握住電極桿另一手拿酒精棉擦洗四個電極片的兩面，然后用蒸餾水沖洗電極片、以及擦洗電解池的杯體和上蓋，清洗完后放入攪拌子，按拆卸步驟裝好電解池。

3、測硫儀電解池氣體過濾器的清洗：當發現電解池的氣體過濾器中有黑色沉積物或堵塞嚴重時，應該清洗氣體過濾器。取下電解池，可不打開上蓋，在電解池中先放一些水，以不漫到氣體過濾器為宜，用滴管往進氣嘴中注入清洗液，待洗液流凈后，再反復加入2～3次，直到無黑色沉淀物或暢通即可，然后用清水沖洗電解池，氣體過濾器應潔白如初。

4、測硫儀氣路的維護：因為儀器氣路系統的狀態直接影響檢測結果的準確性，因此須經常對其進行維護。應定期更換過濾開關內的棉花，一般每檢測200個試樣應更換。同時需對硅膠管進行除灰操作，并檢查該硅膠管與高溫爐相連的一端是否有穿孔，因該端溫度較高，時間長后，管壁會變薄，如有穿孔則需更換，否則可調頭繼續使用。應確保 過濾開關的磨口密封良好，定期加涂凡士林，并檢查其氣密性。